东芝使用8823机芯彩电IIC总线进入与调整

gfhgtr

机芯编号8823机芯存储器数据交换或购买微处理器芯片　小信号处理芯片　存储器型号　所属机型　工厂模式√用户模式　进入方式用手按住电视机上的音量减键，直至屏幕显示到音量为00，不要松手，同时按下遥控器的“DISP”键。此时屏幕右上角会显示“S”字符，即可进入S-MODE维修状态。如图所示：　 RCUT 20 S调节方法及数据 S-MODE是最常用的几个项目，按动节目号加或减键可以选择到所需调整的项目。选择到所需要调整的项目后，再按动音量加或减键，可以调整该项目的数据。下表是S-MODE调整表，以供维修人员参考： 项目数据内容项目数据内容RCUT20红暗平衡HPOS0C50Hz行中心GCUT20绿暗平衡VP500150Hz帧中心BCUT20蓝暗平衡HIT2550Hz帧幅GDVR40绿亮平衡VLIN0C50Hz帧线性BDVR40蓝亮平衡SBY04SECAM B-YCOLC40色度中间值SRY04SECAM R-YTNTC40色调中间值RAGC23高放AGCCOLS40S制色度中间值SCNT00副对比度退出方式　用遥控器关机即可。备 注　【内容导航】 第1页：第2页：D模式参数调整（8823—V2.0）第3页：D 模式参数调整(8823v30)第4页：D 模式参数调整(8823v40)参数名参数描述默认值OSD位置OSD的起始位置00OPT选项OPTION，详细说明附后27RCUTR CUT OFF 红截止20GCUTG CUT OFF 绿截止20BCUTB CUT OFF 兰截止20GDRVG DRIVE 绿驱动40BDRVB DRIVE 兰驱动40CNTXSUB CONTRAST MAX 副对比度最大值32BRTCSUB BRIGHT CENTER 副亮度中间值40COLCSUB COLOR CENTER FOR NTSC 副彩色中间值（NTSC）40TNTCSUB TINT CENTER 副色调中间值40COLPSUB COLOR CENTER FOR PAL 副色度中间值（PAL）00COLSSUB COLOR CENTER FOR SECAM 副色度中间值（SECAM）40SCOLCr input(#21) gain up,000"111:0dB;1.1dB;1.9dB;2.5dB;3.0dB;3.3dB;3.6dB;3.9dBSCNTY-SUB CONTRAST Y信号副对比度 08CNTCSUB CONTRASRT CENTER 副对比度中间值20CNTNSUB CONTRASRT MINIMUM 副对比度最小值08BRTXSUB BRIGHT MAX 副亮度最大值20BRTNSUB BRIGHT MINIMUM 副亮度最小值20COLXSUB COLOR MAX 副色度最大值35COLNSUB COLOR MINIMUM 副色度最小值00TNTXSUB TINT MAX 副色调最大值28TNTNSUB TINT MINIMUM 副色调最小值28ST3SUB SHARP CENTER NTSC3.58 IN TV副画质中间值（NTSC3.58 IN TV）20SV3SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值（NTSC3.58 IN VIDEO）20ST4SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值（OTHER COLOR SYSTEM IN TV）20SV4SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值（OTHER COLOR SYSTEM IN VIDEO）20SVDSUB SHARP CENTER IN DVDASSHASYMMETRY – SHARPNESS 不对称SHPXSUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值1ASHPNSUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值1ATXCXRGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 对比度的最大值3FRGCNRGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 对比度的最小值16ABLABL，详细说明附后DCBSDCBS，详细说明附后CLTOThe data when TV mode & SOUND SYS != M 详细说明附后CLTMThe data when TV mode & SOUND SYS = M 详细说明附后CLVOThe data when YVU mode & SOUND SYS != M 详细说明附后CLVDThe data when YVU mode & SOUND SYS = M 详细说明附后DEF0:V AGC reference,deends on YC VCC;1:Depends on integrated regulatorAKB00:AKB off;01:ACB(cutoff:align to targets);10:ADB(drive:align to targets);11:AKB(cutoff/drive:align to targets)SECDSecam modeHPOS50Hz HORIZONTAL PHASE 50HZ 水平相位（行中心）11VP5050 HZ VERTICAL PHASE 50HZ 场中心03HIT50HZ VERTICAL AMPLITUDE 50HZ 场幅度20HPSSHIFT DAT OF 50/60HZ HORIZONTAL PHASE 行中心偏移量04VP6060HZ VERTICAL PHASE 60HZ 场中心01HITSSHIFT DATA OF 50/60 HZ HORIZONTAL PHASE 场中心偏移量02VLINV-LINEARITY 场线性 50Hz08VSCV-S CORRECTION 场S 50Hz60VLISV-LINEARITY 场线性 60HzFFVSSV-S CORRECTION 场S 60HzSBYSECAM B-Y08SRYSECAM R-Y08BRTSSUB BRIGHTAGCRF AGC ADJUSTMENT RF AGC 调整30HAFC1/2 AFC DATA ADJUSTMENT AFC调整00V25VOLUME OUTPUT DATA AT 25%3DV50VOLUME OUTPUT DATA AT 50%57V100VOLUME 100MUTTY-MUTE FOR SOFT STARTSTATCONTRAST UP FOR SOFT STARTFLG0Flag0FLG1Flag1REFPAKB Ref Pulse PositionRSNSR SENSGSNSG SENSBSNSB SENSMOD00:akb CUTOFF SENSITIVITY,*9.75;01:*10.00;10:*10.25;11:*10.50; MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.85STBYBit0,1:IF Standby; Bit2,3: VCD StandbySVMPIC1 SVMVBLKV BLANKING START AND STOP POINTVCENV CENTERINGHSIZPICTURE WIDTHPRBRE-W PARABOLATRUMTRAPEZIUMECCTEW-CORNER CORRECTION(TOP)ECCBEW-CORNER CORRECTION(BOTTOM)EHT高压下尺寸的调整UCOM00:GND;01:R OUTPUT;10:B OUTPUT;11:MONITOR RF AGC VIA ADCPYNXNormal H.SYNC maxPYNNNormal H.SYNC minPYXSSearch H.SYNC maxPYNSSearch H.SYNC minRCUTSRCUTSGCUTSGCUTSBCUTSGDRVSGDRVSGDRVSBDRVSBDRVSNOIS信号强弱界限设定AKB_OPTION不起作用AV_OPT详情附后OPT2详情附后WAIT TIME开机等待时间3FCUR_CEN拉幕位置CUR_STEP拉幕速度AUSTPMODE0详情附后MODE1详情附后OSDFOSD频率 OPT：BITFUNCTION0Mute ON/OFF when B.B is OFFｉｎ　ＮＯSignal(=1:OFF)1EXT_Mute ON/OFF when B.B is OFFｉｎ　ＮＯSignal(=1:OFF)2V_Mute ON/OFF when ＣＨ changes(=1:ON)3AUDIO GAIN SW of tb12404Not VT Down of AFT when No Signal(=1)5TINT 0:use 1:unused6Select TV sync(0) or MONITOR sync(1)7Mute of av switch key 1.use 0.no use ABL：BITFUNCTION0ABL-Gain 00:-0.2;01:-0.4;10:-0.6;11:-0.8v12ABL Start Point 00:-0.0;01:-0.15;10:-0.3;11:-0.45v34WPS5RGB ABCL61：计时收看清到20H；0：计时收看清到0H71：用户可按SLEEP键清除收看计时；0：不可 DCBSBITFUNCTION0BLACK STRETCH00：Off；01：Black stretch point,25IRE;02:35 IRE;03:45 IRE12Y GAMMA00：Off；01：Y y point 90 IRE,Gain –3dB;02:80 IRE;03:70 IRE34OSD CONTRAST00:80 IRE 01:70;02:60;03:50;56UNUSE7BLK CLTO\CLTM\CLVO\CLVDBITFUNCTION0Y Delay Time000:-40 nsec;001:0;010:40 nsec;011:80 nsec;100:120 nsec;101:160 nsec;110:200 nsec;111:240 nsec123N Phase00:USA(105 degree);01:Japan(93 degree);10:11:DVD45Color Y 0:Color gamma off ;1:On;6PN-ID Sens 0:PAL/NTSC killer sensitivity,1mVpp; 1:10mVpp7FID 0:Normal;1:Alwas killer off,i.e. always color on.. FLG0:BITFUNCTION00:NORMAL;1:PIF over modulation switch on10:BPF;1:TOF20:Nyquist Buzz CANcel,on;2:off3Q det Gain4L SECAM Mode5SIF FIX Select 0:fix to normal, 1:control with sound system6SIF 5.74 Select In D mode, aPLLy this bit to SIF 5747vco readjust when position select 0:dISAble;1:enable; FLG1:BITFUNCTION0CW SW1YOUT ON2HD input polarity select30:SIF beat down Frequency,1MHz;1:+62.5kHz shift40:Sync separation level,40%;1:36%50:SIF 1MHz convert gain,Low gain;1:High gain for Evalution6DET358 for Evalution7C TRAP PASS for Evalution SVM:BITFUNCTION000:-6dB;01:0dB;10:+6dB;11:+12dB1200:off;01:-100ns;10:-60ns;11:-40ns34CO MAX51：有计时收看功能；0：无61：有软换台功能；0：无7UNUSE VBLKBITFUNCTION000:23H;01:33H;10:37H;11:41H (50Hz)00:22H;01:30H;10:34H;11:38H (60Hz)1200:310H;01:299H;10:295H;11:291H (50Hz)00:263H;01:254H;10:250H;11:246H (60Hz)345 MODE0:BITFUNCTION01：218频道；0：100频道11：M制（Fjp_5060）0：AV开关选择 20：有SECAM制；1：无31：RGB Out-Cut Off DC；0：Y-MUTE41：有些屏显一直显示；0：有些屏显有时显示5UNUSE6SHOP OUT00：DK；01：I；10：BG7 MODE1:BITFUNCTION00:无BG;1:有10:无I;1:有20:无DK;1:有30:无M;1:有40:when asm & search,set up VCO adjust req. ,1:only power on5The algorithm of ASM. 0:ASM doesn't judge IFLOCK with case 4. 1:ASM judge IF LOCK with case 46The algorithm of ASM. 0:ASM doesn't judge Fhsync with case 4. 1:ASM judge Fhsync with case 47TINT polarity ,input to V/C/D. 0:normal 1:invert AV_OPT：ByteFUNCTIONVideo1Video2Video30VIDEODVD1VIDEOS-VIDEODVD2VIDEODVDVIDEO3VIDEOS-VIDEODVD4VIDEO/S-VIDEODVD5VIDEO/S-VIDEOVIDEODVD6VIDEODVDVIDEO7VIDEOVIDEODVDOPT2BITFUNCTION0开机延长时间121：只有英文；0：英文、中文均有3AV是否静噪；1：静噪；0：不4有无背景灯；1：有；0：无（当设置为0时，59脚控制伴音制式）567一直设置为0。 MOD：BITFUNCTION0akb CUTOFF SENSITI VITY00：*9.75;01:*10.00;10:*10.25;11:*10.50123MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.854000：无；001：45.75；011：38.9；100：38.0567上一页1【内容导航】 第1页：第2页：D模式参数调整（8823—V2.0）第3页：D 模式参数调整(8823v30)第4页：D 模式参数调整(8823v40)参数名参数描述默认值OSD位置OSD的起始位置00OPT选项OPTION，详细说明附后27RCUTR CUT OFF 红截止20GCUTG CUT OFF 绿截止20BCUTB CUT OFF 兰截止20GDRVG DRIVE 绿驱动40BDRVB DRIVE 兰驱动40CNTXSUB CONTRAST MAX 副对比度最大值7FBRTCSUB BRIGHT CENTER 副亮度中间值50COLCSUB COLOR CENTER FOR NTSC 副彩色中间值（NTSC）40TNTCSUB TINT CENTER 副色调中间值40COLPSUB COLOR CENTER FOR PAL 副色度中间值（PAL）20COLSSUB COLOR CENTER FOR SECAM 副色度中间值（SECAM）40SCOLCr input(#21) gain up,000"111:0dB;1.1dB;1.9dB;2.5dB;3.0dB;3.3dB;3.6dB;3.9dB07SCNTY-SUB CONTRAST Y信号副对比度 0ECNTCSUB CONTRASRT CENTER 副对比度中间值50CNTNSUB CONTRASRT MINIMUM 副对比度最小值01BRTXSUB BRIGHT MAX 副亮度最大值35BRTNSUB BRIGHT MINIMUM 副亮度最小值35COLXSUB COLOR MAX 副色度最大值7FCOLNSUB COLOR MINIMUM 副色度最小值00TNTXSUB TINT MAX 副色调最大值40TNTNSUB TINT MINIMUM 副色调最小值40ST3SUB SHARP CENTER NTSC3.58 IN TV副画质中间值（NTSC3.58 IN TV）25SV3SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值（NTSC3.58 IN VIDEO）25ST4SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值（OTHER COLOR SYSTEM IN TV）25SV4SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值（OTHER COLOR SYSTEM IN VIDEO）25SVDSUB SHARP CENTER IN DVD26ASSHASYMMETRY – SHARPNESS 不对称07SHPXSUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值38SHPNSUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值15TXCXRGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 对比度的最大值1FRGCNRGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 对比度的最小值1FABLABL，详细说明附后37DCBSDCBS，详细说明附后33CLTOThe data when TV mode & SOUND SYS != M 详细说明附后0BCLTMThe data when TV mode & SOUND SYS = M 详细说明附后4BCLVOThe data when YVU mode & SOUND SYS != M 详细说明附后4BCLVDThe data when YVU mode & SOUND SYS = M 详细说明附后4BDEF0:V AGC reference,deends on YC VCC;1:Depends on integrated regulator01AKB00:AKB off;01:ACB(cutoff:align to targets);10:ADB(drive:align to targets);11:AKB(cutoff/drive:align to targets)00SECDSecam mode18HPOS50Hz HORIZONTAL PHASE 50HZ 水平相位（行中心）11VP5050 HZ VERTICAL PHASE 50HZ 场中心03HIT50HZ VERTICAL AMPLITUDE 50HZ 场幅度20HPSSHIFT DAT OF 50/60HZ HORIZONTAL PHASE 行中心偏移量04VP6060HZ VERTICAL PHASE 60HZ 场中心01HITSSHIFT DATA OF 50/60 HZ HORIZONTAL PHASE 场中心偏移量02VLINV-LINEARITY 场线性 50Hz08VSCV-S CORRECTION 场S 50Hz60VLISV-LINEARITY 场线性 60HzFFVSSV-S CORRECTION 场S 60HzSBYSECAM B-Y08SRYSECAM R-Y08BRTSSUB BRIGHT00AGCRF AGC ADJUSTMENT RF AGC 调整30HAFC1/2 AFC DATA ADJUSTMENT AFC调整09V25VOLUME OUTPUT DATA AT 25%3DV50VOLUME OUTPUT DATA AT 50%57V100VOLUME 1007FMUTTY-MUTE FOR SOFT START00STATCONTRAST UP FOR SOFT START00FLG0Flag052FLG1Flag124REFPAKB Ref Pulse Position00RSNSR SENS00GSNSG SENS00BSNSB SENS00MOD00:akb CUTOFF SENSITIVITY,*9.75;01:*10.00;10:*10.25;11:*10.50; MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.8540STBYBit0,1:IF Standby; Bit2,3: VCD Standby00SVMPIC1 SVM60VBLKV BLANKING START AND STOP POINT00VCENV CENTERING27HSIZPICTURE WIDTH20PRBRE-W PARABOLA20TRUMTRAPEZIUM10ECCTEW-CORNER CORRECTION(TOP)00ECCBEW-CORNER CORRECTION(BOTTOM)00EHT高压下尺寸的调整24UCOM00:GND;01:R OUTPUT;10:B OUTPUT;11:MONITOR RF AGC VIA ADC00PYNXNormal H.SYNC max2EPYNNNormal H.SYNC min18PYXSSearch H.SYNC max22PYNSSearch H.SYNC min1ERCUTSRCUTS10GCUTSGCUTS00BCUTSGDRVS10GDRVSGDRVS00BDRVSBDRVS00NOIS信号强弱界限设定01AKB_OPTION不起作用00AV_OPT详情附后04OPT2详情附后1BWAIT TIME开机等待时间38CUR_CEN拉幕位置A0CUR_STEP拉幕速度01AUSTP0AMODE0详情附后MODE1详情附后OSDFOSD频率58 OPT：BITFUNCTION0Use Energy Flag 1:have energy1Real Time CLOCk 1:have real time clock2V_Mute ON/OFF when ＣＨ changes(=1:ON)3AUDIO GAIN SW of tb12404Not VT Down of AFT when No Signal(=1)5TINT 0:use 1:unused6Select TV sync(0) or MONITOR sync(1)7Mute of av switch key 1.use 0.no useABL：BITFUNCTION0ABL-Gain 00:-0.2;01:-0.4;10:-0.6;11:-0.8v12ABL Start Point 00:-0.0;01:-0.15;10:-0.3;11:-0.45v34WPS 0:Y peak limiter off 1:Y peak limiter on,105IRE5RGB ABCL 0:ABCL active for OSD 0:inactive61：计时收看清到20H；0：计时收看清到0H71：用户可按SLEEP键清除收看计时；0：不可DCBS？BITFUNCTION0BLACK STRETCH 黑电平延伸00：Off；01：Black stretch point,26IRE; 10 : 33 IRE; 11 : 43 IRE12Y GAMMA00：Off；01：Y γ point 90 IRE,Gain –3dB; 10 : 82 IRE ; 11 : 75 IRE34OSD CONTRAST00:80 IRE 01:70;02:60;03:50;56UNUSE7BLKCLTO\CLTM\CLVO\CLVDBITFUNCTION0Y Delay Time000:-40 nsec;001:0;010:40 nsec;011:80 nsec;100:120 nsec;101:160 nsec;110:200 nsec;111:240 nsec123N Phase00:USA(105 degree);01:Japan(93 degree);10:11:DVD45Color Y 0:Color gamma off ;1:On;6PN-ID Sens 0:PAL/NTSC killer sensitivity,1mVpp; 1:10mVpp7FID 0:Normal;1:Alwas killer off,i.e. always color on..FLG0:BITFUNCTION00:NORMAL;1:PIF over modulation switch on10:BPF;1:TOF20:Nyquist Buzz CANcel,on;2:off3Q det Gain4L SECAM Mode5SIF FIX Select 0:fix to normal, 1:control with sound system6SIF 5.74 Select In D mode, aPLLy this bit to SIF 5747vco readjust when position select 0:dISAble;1:enable;FLG1:BITFUNCTION0CW SW1YOUT ON2HD input polarity select30:SIF beat down Frequency,1MHz;1:+62.5kHz shift40:Sync separation level,40%;1:36%50:SIF 1MHz convert gain,Low gain;1:High gain for Evalution6DET358 for Evalution7C TRAP PASS for EvalutionSVM:BITFUNCTION0SVM gain00:-6dB;01:0dB;10:+6dB;11:+12dB12SVM DL(svm delay)00:off;01:-100ns;10:-60ns;11:-40ns34CO MAX 0:cut off range is –0.65"+0.65 ; 1: cut off range is –0.65"+0.8551：有计时收看功能；0：no the total time of watch TV61：有软换台功能；0：no the soft change channel7UNUSEVBLKBITFUNCTION000:23H;01:33H;10:37H;11:41H (50Hz)00:22H;01:30H;10:34H;11:38H (60Hz)1200:310H;01:299H;10:295H;11:291H (50Hz)00:263H;01:254H;10:250H;11:246H (60Hz)345MODE0:BITFUNCTION01：218频道；0：100频道11：50hz/60hz （M制）；0：两路AV （无M制时，几路AV用AV option来控制 ）20：有SECAM制；1：无31：RGB Out-Cut Off DC；0：Y-MUTE41：有些屏显一直显示；0：有些屏显有时显示5UNUSE6SHOP OUT00：DK；01：I；10：BG7MODE1:BITFUNCTION00:无BG;1:有10:无I;1:有20:无DK;1:有30:无M;1:有40:when asm & search,set up VCO adjust req. ,1:only power on0:PIF VCO adjust trigger 1: normal (12 :bit 7)5The algorithm of ASM. 0:ASM doesn't judge IFLOCK with case 4. 1:ASM judge IF LOCK with case 46The algorithm of ASM. 0:ASM doesn't judge Fhsync with case 4. 1:ASM judge Fhsync with case 47TINT polarity ,input to V/C/D. 0:normal 1:invertAV_OPT：ByteFUNCTIONVideo1Video2Video30VIDEODVD1VIDEOS-VIDEODVD2VIDEODVDVIDEO3VIDEOS-VIDEODVD4VIDEO/S-VIDEODVD5VIDEO/S-VIDEOVIDEODVD6VIDEODVDVIDEO7VIDEOVIDEODVDOPT2:BITFUNCTION0lunar calendar 1:have lunar calendar ; 0:no lunar calendar11:调整时间时不可以在电视机上显示 0：调整时间时可以在电视机上显示 21：只有英文 0：有中文3AV是否静噪；1：静噪；0：不4有无背景灯；1：有；0：无5No use6No use7No use一直设置为0即可。MOD：BITFUNCTION0akb CUTOFF SENSITI VITY00：*9.75;01:*10.00;10:*10.25;11:*10.50123MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.854000：无；001：45.75；011：38.9；100：38.0567上一页12【内容导航】 第1页：第2页：D模式参数调整（8823—V2.0）第3页：D 模式参数调整(8823v30)第4页：D 模式参数调整(8823v40)参数名参数描述默认值OSD位置OSD的起始位置10OPT选项OPTION，详细说明附后FCRCUTR CUT OFF 红截止20GCUTG CUT OFF 绿截止20BCUTB CUT OFF 兰截止20GDRVG DRIVE 绿驱动40BDRVB DRIVE 兰驱动40CNTXSUB CONTRAST MAX 副对比度最大值7FBRTCSUB BRIGHT CENTER 副亮度中间值50COLCSUB COLOR CENTER FOR NTSC 副彩色中间值（NTSC）40TNTCSUB TINT CENTER 副色调中间值40COLPSUB COLOR CENTER FOR PAL 副色度中间值（PAL）20COLSSUB COLOR CENTER FOR SECAM 副色度中间值（SECAM）40SCOLCr input(#21) gain up,000"111:0dB;1.1dB;1.9dB;2.5dB;3.0dB;3.3dB;3.6dB;3.9dB07SCNTY-SUB CONTRAST Y信号副对比度 0ECNTCSUB CONTRASRT CENTER 副对比度中间值50CNTNSUB CONTRASRT MINIMUM 副对比度最小值01BRTXSUB BRIGHT MAX 副亮度最大值35BRTNSUB BRIGHT MINIMUM 副亮度最小值35COLXSUB COLOR MAX 副色度最大值7FCOLNSUB COLOR MINIMUM 副色度最小值00TNTXSUB TINT MAX 副色调最大值40TNTNSUB TINT MINIMUM 副色调最小值40ST3SUB SHARP CENTER NTSC3.58 IN TV副画质中间值（NTSC3.58 IN TV）25SV3SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值（NTSC3.58 IN VIDEO）25ST4SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值（OTHER COLOR SYSTEM IN TV）25SV4SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值（OTHER COLOR SYSTEM IN VIDEO）25SVDSUB SHARP CENTER IN DVD26ASSHASYMMETRY – SHARPNESS 不对称07SHPXSUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值38SHPNSUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值15TXCXRGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 对比度的最大值1FRGCNRGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 对比度的最小值1FABLABL，详细说明附后37DCBSDCBS，详细说明附后33CLTOThe data when TV mode & SOUND SYS != M 详细说明附后0BCLTMThe data when TV mode & SOUND SYS = M 详细说明附后4BCLVOThe data when YVU mode & SOUND SYS != M 详细说明附后4BCLVDThe data when YVU mode & SOUND SYS = M 详细说明附后4BDEF0:V AGC reference,deends on YC VCC;1:Depends on integrated regulator01AKB00:AKB off;01:ACB(cutoff:align to targets);10:ADB(drive:align to targets);11:AKB(cutoff/drive:align to targets)00SECDSecam mode18HPOS50Hz HORIZONTAL PHASE 50HZ 水平相位（行中心）11VP5050 HZ VERTICAL PHASE 50HZ 场中心03HIT50HZ VERTICAL AMPLITUDE 50HZ 场幅度20HPSSHIFT DAT OF 50/60HZ HORIZONTAL PHASE 行中心偏移量04VP6060HZ VERTICAL PHASE 60HZ 场中心01HITSSHIFT DATA OF 50/60 HZ HORIZONTAL PHASE 场中心偏移量02VLINV-LINEARITY 场线性 50Hz08VSCV-S CORRECTION 场S 50Hz60VLISV-LINEARITY 场线性 60HzFFVSSV-S CORRECTION 场S 60Hz00SBYSECAM B-Y08SRYSECAM R-Y08BRTSSUB BRIGHT00AGCRF AGC ADJUSTMENT RF AGC 调整30HAFC1/2 AFC DATA ADJUSTMENT AFC调整09V25VOLUME OUTPUT DATA AT 25%3FV50VOLUME OUTPUT DATA AT 50%57V100VOLUME 1007FMUTTY-MUTE FOR SOFT START00STATCONTRAST UP FOR SOFT START00FLG0Flag052FLG1Flag104REFPAKB Ref Pulse Position00RSNSR SENS00GSNSG SENS00BSNSB SENS00MOD00:akb CUTOFF SENSITIVITY,*9.75;01:*10.00;10:*10.25;11:*10.50; MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.8540STBYBit0,1:IF Standby; Bit2,3: VCD Standby00SVMPIC1 SVM60VBLKV BLANKING START AND STOP POINT00VCENV CENTERING27HSIZPICTURE WIDTH20PRBRE-W PARABOLA20TRUMTRAPEZIUM10ECCTEW-CORNER CORRECTION(TOP)00ECCBEW-CORNER CORRECTION(BOTTOM)00EHT高压下尺寸的调整24UCOM00:GND;01:R OUTPUT;10:B OUTPUT;11:MONITOR RF AGC VIA ADC00PYNXNormal H.SYNC max28PYNNNormal H.SYNC min18PYXSSearch H.SYNC max22PYNSSearch H.SYNC min1ERCUTSRCUTS10GCUTSGCUTS00BCUTSGDRVS10GDRVSGDRVS00BDRVSBDRVS00NOIS信号强弱界限设定01AKB_OPTION不起作用00AV_OPT详情附后04OPT2详情附后09WAIT TIME开机等待时间3FCUR_CEN拉幕位置A5CUR_STEP拉幕速度01PBRI连续按0键 图像所恢复的亮度数值PCOL连续按0键 图像所恢复的彩色数值PCON连续按0键 图像所恢复的对比度数值PSHP连续按0键 图像所恢复的清晰度数值PTIN连续按0键 图像所恢复的色调数值PVOLunusedAUSTP04MODE0详情附后3FMODE1详情附后OSDFOSD频率 数值越大屏幕上字符越小65上一页123【内容导航】 第1页：第2页：D模式参数调整（8823—V2.0）第3页：D 模式参数调整(8823v30)第4页：D 模式参数调整(8823v40)