东芝使用8829B机芯彩电IIC总线进入与调整

dfgfhe44d

机芯编号8829B机芯存储器数据交换或购买微处理器芯片　小信号处理芯片　存储器型号　所属机型　工厂模式√用户模式　进入方式用手按住电视机上的音量减键，直至屏幕显示到音量为00，不要松手，同时按下遥控器的“DISP”键。此时屏幕右上角会显示“S”字符，即可进入S-MODE维修状态。如图所示：　 RCUT 20 S调节方法及数据 S-MODE是最常用的几个项目，按动节目号加或减键可以选择到所需调整的项目。选择到所需要调整的项目后，再按动音量加或减键，可以调整该项目的数据。下表是S-MODE调整表，以供维修人员参考： 项目数据内容项目数据内容RCUT20红暗平衡HPOS0C50Hz行中心GCUT20绿暗平衡VP500150Hz帧中心BCUT20蓝暗平衡HIT2550Hz帧幅GDVR40绿亮平衡VLIN0C50Hz帧线性BDVR40蓝亮平衡SBY04SECAM B-YCOLC40色度中间值SRY04SECAM R-YTNTC40色调中间值RAGC23高放AGCCOLS40S制色度中间值SCNT00副对比度退出方式　用遥控器关机即可。备 注　【内容导航】 第1页：第2页：8829BV1.0软件D 模式参数调整第3页：D(8829B-2.0) 模式参数调整参数名参数描述默认值OSD位置OSD的起始位置20OPT选项OPTION，详细说明附后DC/FCRCUTR CUT OFF 红截止(00-FF)66GCUTG CUT OFF 绿截止(00-FF)37BCUTB CUT OFF 兰截止(00-FF)29GDRVG DRIVE 绿驱动(00-7F)3BBDRVB DRIVE 兰驱动(00-7F)40CNTXSUB CONTRAST MAX 副对比度最大值(00-7F)7FBRTCSUB BRIGHT CENTER 副亮度中间值(00-7F)5ACOLCSUB COLOR CENTER FOR NTSC 副彩色NTSC中间值(00-7F)42TNTCSUB TINT CENTER 副色调中间值(00-7F)42COLPSUB COLOR CENTER FOR PAL 副色度PAL中间值(80-00-7F)08COLSSUB COLOR CENTER FOR SECAM 副色度SECAM中间值(00-7F)31DCOLDVD-色度中心值45SCOLCr input(#21) gain up,000"111:0dB;1.1dB;1.9dB;2.5dB;3.0dB;3.3dB;3.6dB;3.9dB07SCNTY-SUB CONTRAST Y信号副对比度(00-7F)0ECNTCSUB CONTRASRT CENTER 副对比度中间值(00-7F)50CNTNSUB CONTRASRT MINIMUM 副对比度最小值(00-7F)00BRTXSUB BRIGHT MAX 副亮度最大值(00-7F离中间值上限)40BRTNSUB BRIGHT MINIMUM 副亮度最小值（00-7F离中间值下限）40COLXSUB COLOR MAX 副色度最大值3FCOLNSUB COLOR MINIMUM 副色度最小值(00-7F)00TNTXSUB TINT MAX 副色调最大值(00-7F离中间值上限)40TNTNSUB TINT MINIMUM 副色调最小值(00-7F离中间值下限)40ST3SUB SHARP CENTER NTSC3.58 IN TV副画质中间值（NTSC3.58 IN TV）(00-3F)20SV3SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值（NTSC3.58 IN VIDEO）(00-3F)20ST4SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值（OTHER COLOR SYSTEM IN TV）(00-3F)20SV4SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值（OTHER COLOR SYSTEM IN VIDEO）(0-3F)20SVDSUB SHARP CENTER IN DVD (00-3F)19ASSHASYMMETRY – SHARPNESS 不对称(单边清晰度)07SHPXSUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值38SHPNSUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值1ATXCXRGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 对比度的最大值图文状态（UNUSEFUL）1FRGCNRGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 对比度的最小值图文状态（UNUSEFUL）00ABLABL，详细说明附后37DCBSDCBS，详细说明附后23CLTOThe data when TV mode & SOUND SYS NOT M 详细说明附后06CLTMThe data when TV mode & SOUND SYS IS M 详细说明附后06CLVOThe data when NOT YVU mode 详细说明附后47CLVDThe data when YVU mode 详细说明附后41OPT2详细说明附后03AKB00:AKB off;01:ACB(cutoff:align to targets);10:ADB(drive:align to targets);11:AKB(cutoff/drive:align to targets)00SECDSecam mode BIT0：S-ID Sens，BIT1：Bell fo，BIT2：S-ID ModeBIT3：S-GP phase 08HPOS50Hz HORIZONTAL PHASE 50HZ 水平相位（行中心）00:-3usec; 10:0; 1F:+3usec0EVP5050 HZ VERTICAL PHASE 50HZ 场中心0:V phase delay 0H; 7: 7H06HIT50HZ VERTICAL AMPLITUDE 50HZ 场幅度00:-50%; 20: 0%; 3F:50&HPSSHIFT DAT OF 60HZ HORIZONTAL PHASE 行中心偏移量(60Hz和50Hz的差异)03VP6060HZ VERTICAL PHASE 60HZ 场中心0:V phase delay 0H; 7: 7H03HITS60HZ VERTICAL AMPLITUDE 60HZ场幅度(60Hz和50Hz的差异)00VLINV-LINEARITY 场线性 50Hz 0:-15%; 8:0%; F:15%09VSCV-S CORRECTION 场S 50Hz 0:-16%; 8:0%; F:16%09VLISV-LINEARITY 场线性 60Hz (60Hz和50Hz的差异)00VSSV-S CORRECTION 场S 60Hz (60Hz和50Hz的差异)00DPC50HZ E-W CORRECTION 东西枕校00:0VP-P;20:1.4VP-P;3F:2.8VP-P1EDPCS60HZ E-W CORRECTION (60Hz和50Hz的差异)01KEY50HZ TRAPEZIUM CORRECTION 梯形校正00:13%; 20:0%; 3F:13%24KEYS60HZ TRAPEZIUM CORRECTION 梯形校正(60Hz和50Hz的差异)01WID50HZ PICTURE WIDTH 行幅00:1.5VP-P;20:4VP-P;3F:6.5VP-P15WIDS60HZ PICTURE WIDTH 行幅 (60Hz和50Hz的差异)01ECCTEW-CORNER CORRECTION TOP 顶部两角校正00:-1.5VP-P;20:0VP-P;3F:1.5VP-P0BECCBEW-CORNER CORRECTION BOTTOM 底部两角校正00:-1.5VP-P;20:0VP-P;3F:1.5VP-P0EVEHT帧幅随高压波动的幅度（改变图象模式可以看出）03HEHT行幅随高压波动的幅度00SBYSECAM B-Y08SRYSECAM R-Y08BRTSSUB BRIGHT (C0-00-3F)00RAGCRF AGC ADJUSTMENT RF AGC 调整00:IF mute; 01: 65dB; 3F: 100dB30HAFC1/2 AFC DATA ADJUSTMENT AFC调整BIT1,0:TV MODE BIT2,3:AV MODE00V01VOLUME OUTPUT DATA AT 1%10V25VOLUME OUTPUT DATA AT 25%3FV50VOLUME OUTPUT DATA AT 50%48V100VOLUME 10054MUTTY-MUTE TIME OF SOFT START00STATCONTRAST UP TIME OF SOFT START00FLG0Flag0 (00-FF) 详情附后52FLG1Flag1 (00-FF) 详情附后24REFPAKB Pulse Position (00-07)00RSNSR SENS (00-3F)00GSNSG SENS (00-3F)00BSNSB SENS (00-3F)00MOD00:akb CUTOFF SENSITIVITY,*9.75;01:*10.00;10:*10.25;11:*10.50; MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.8500STBYBit0,1:IF Standby; Bit2,3: VCD Standby00SVMPIC1 SVM00VBLKV BLANKING START AND STOP POINT00VCENV CENTERING场输出脚直流电平（为1/2VCC）（不好卷边）19UCOM1COSD2GAME AND CALENGDAR POSITION18PYNXNormal H.SYNC max判断蓝屏出现28PYNNNormal H.SYNC min判断蓝屏出现18PYXSSearch H.SYNC max搜索状态同步判断22PYNSSearch H.SYNC min搜索状态同步判断1EWCTL"COM2NO USE（TOGETHER 23 ITEMS）00MODE0详情附后31MODE1详情附后2DMODE2详情附后FFRCUTSRCUTS00GCUTSGCUTS00BCUTSGDRVS00GDRVSGDRVS00BDRVSBDRVS10NOIS信号强弱界限设定01OSDFOSD频率；数字小，字符增大，右移。58WAIT TIME开机等待时间38CUR_CEN拉幕位置ACCUR_STEP拉幕速度01 OPT：BITFUNCTION0能源之星 0：无 ；1：有 1实时时钟 0：无 ；1：有2V_Mute ON/OFF when ＣＨ changes(=1:ON) ；1频道切换黑屏3AUDIO GAIN SW of 2 IN1 FOR M SYS 0：NOMAL 1：HIGH4NOT VT Down of AFT when No Signal(=1) ；1无信号AFT不自动向下找台5TUNER 0：ALPS 1：SAMSUNG6Select TV sync(0) or MONITOR sync(1) ；同步方式，选择17记时收看：0：无 ；1：有 ABL：BITFUNCTION0ABL-Gain 00:-0.2;01:-0.4;10:-0.6;11:-0.8v 选择1112ABL Start Point 00:-0.0;01:-0.15;10:-0.3;11:-0.45v 选择0134WPS白峰抑制0:OFF,1:ON（主要针对显象管，显象管高亮底色变化时，打开限幅）5RGB ABCL 0：OFF；1：ON 选择16NO USE71：用户可按SLEEP键清除收看计时；0：不可 ；选择0 DCBSBITFUNCTION0BLACK STRETCH00：Off；01：Black stretch point,25IRE;10:35 IRE; 11:45 IRE 选择1112Y GAMMA00：Off；01：Y y point 90 IRE,Gain –3dB;10:80 IRE;11:70 IRE 选择0034OSD CONTRAST00:80 IRE 01:70 IRE;10:60 IRE;11:50 IRE; 选择1056UNUSE7BLK 0：H、V BLANKING ON ；1：H、V BLANKING OFF 选择0 CLTO\CLTM\CLVO\CLVDBITFUNCTION0Y Delay Time000:-40 nsec;001:0;010:40 nsec;011:80 nsec;100:120 nsec;101:160 nsec;110:200 nsec;111:240 nsec 123NTSC Phase00:USA(105 degree);01:Japan(93 degree);10:11:DVD45Color γ 0:Color gamma off ;1:On;6PAL/NTSC-ID Sens 0:PAL/NTSC killer sensitivity,1mVpp; 1:10mVpp7FID 0:Normal;1:Alwas killer off,i.e. always color on.. FLG0:BITFUNCTION00:NORMAL;1:PIF over modulation switch on 010:BPF;1:TOF 120:Nyquist Buzz CANcel,on;1:off 03Q det Gain4L secam Mode5SIF FIX SELECT 0:FIX TO NORMAL 1:CONTROL WITH SOUND SYSTEM6SIF 5.74MHZ SELECT IN D MODE APPLY THIS BIT TO SIF 5747vco readjust when position select 0:dISAble;1:enable; 0 FLG1:BITFUNCTION0CW SW 0:OFF; 1:ON ,CW OUTPUT FROM”TV IN”(PIN 26) 01Y OUT ON 02HD INPUT POLARITY 030:SIF beat down Frequency,1MHz;1:+62.5kHz shift 140:Sync separation level,40%;1:36% 050:SIF 1MHz convert gain,Low gain;1:High gain for Evalution 16DET 3.58 FOR EVALUTION 07C TRAP PASS FOR EVALUTION 0 VBLKBITFUNCTION000:23H;01:33H;10:37H;11:41H (50Hz)00:22H;01:30H;10:34H;11:38H (60Hz) 001200:310H;01:299H;10:295H;11:291H (50Hz)00:263H;01:254H;10:250H;11:246H (60Hz) 0034/5UNUSEBITFUNCTION01：有拉幕式；0：无1UNUSE21：有SECAM制；0：无31：南美制式设成AUTO；0：不转成AUTO41：218频道；0：100频道51：RGB Out-Cut Off DC；0：Y-MUTE ；选择1，否则换台、拉幕可能灰屏6有无背景灯；1：有；0：无7SVM 1:YES 0:NO MODE1：BITFUNCTION01：有YUV输入；0：无1UNUSE21：有些屏显一直显示；0：有些屏显有时显示 ；选择0，日历、屏显能自动消失3TINT FOR PAL SYS 1：NO USE ；0：USE4TINT polarity，input to　Ｖ/C/D 1：INVERT 0：NOMAL5AV MUTE 0：NO；1：YES6/7SHOP OUT00:DK 01:I 10:BG 11:M MODE2:BITFUNCTION00:无M; 1:有 110:无I; 1:有 1 20:无BG; 1:有 130:无DK; 1:有 140:when asm & search,set up VCO adjust req. ,1:only power on 15The algorithm of ASM. 0:ASM doesn't judge IFLOCK with case 4. 1:ASM judge IF LOCK with case 4 16The algorithm of ASM. 0:ASM doesn't judge Fhsync with case 4. 1:ASM judge Fhsync with case 4 17软换台 1：有；0：无 OPT2:BITFUNCTION0DEF:1 （选择0猫头圆图抖动）1农历：12只有英文：0：NO，1：YES3LCD PANEL ON REMOTE CONTROL：0：NO，1：YES4NO USE5NO USE6NO USE7NO USE上一页1【内容导航】 第1页：第2页：8829BV1.0软件D 模式参数调整第3页：D(8829B-2.0) 模式参数调整参数名参数描述默认值OSD位置OSD的起始位置00OPT选项OPTION，详细说明附后27RCUTR CUT OFF 红截止 (00-FF)20GCUTG CUT OFF 绿截止 (00-FF)20BCUTB CUT OFF 兰截止 (00-FF)20GDRVG DRIVE 绿驱动 (00-7F)40BDRVB DRIVE 兰驱动 (00-7F)40CNTXSUB CONTRAST MAX 副对比度最大值 (00-7F)32BRTCSUB BRIGHT CENTER 副亮度中间值 (00-7F)40COLCSUB COLOR CENTER FOR NTSC 副彩色中间值（NTSC）(00-7F)40TNTCSUB TINT CENTER 副色调中间值 (00-7F)40COLPSUB COLOR CENTER FOR PAL 副色度中间值（PAL）00COLSSUB COLOR CENTER FOR SECAM 副色度中间值（SECAM）40DCOLDVD 色度中间值 （太小：图象发虚，缺乏层次）SCOLCr input gain up 000-111：0dB；1.1 dB；1.9 dB；2.5 dB； 3.0 dB；3.3 dB；3.6 dB；3.9 dB；SCNTY-SUB CONTRAST Y信号副对比度 (00-7F)08CNTCSUB CONTRASRT CENTER 副对比度中间值 (00-7F)20CNTNSUB CONTRASRT MINIMUM 副对比度最小值 (00-7F)08BRTXSUB BRIGHT MAX 副亮度最大值 (00-7F 离中间值上限)20BRTNSUB BRIGHT MINIMUM 副亮度最小值(00-7F 离中间值下限)20COLXSUB COLOR MAX 副色度最大值 35COLNSUB COLOR MINIMUM 副色度最小值 (00-7F)00TNTXSUB TINT MAX 副色调最大值 (00-7F 离中间值上限)28TNTNSUB TINT MINIMUM 副色调最小值 (00-7F 离中间值下限)28ST3SUB SHARP CENTER NTSC3.58 IN TV副画质中间值（NTSC3.58 IN TV） (00-3F)20SV3SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值（NTSC3.58 IN VIDEO）(00-3F)20ST4SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值（OTHER COLOR SYSTEM IN TV）(00-3F)20SV4SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值（OTHER COLOR SYSTEM IN VIDEO）(00-3F)20SVDSUB SHARP CENTER IN DVD (00-3F)19ASSHASYMMETRY – SHARPNESS 不对称（单边清晰度）07SHPXSUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值1ASHPNSUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值1ATXCXRGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 图文状态对比度的最大值 （ unused）3FRGCNRGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 图文状态对比度的最小值 (unused)00ABLABL，详细说明附后37DCBSDCBS，详细说明附后33CLTOThe data when TV mode & SOUND SYS != M 详细说明附后4BCLTMThe data when TV mode & SOUND SYS = M 详细说明附后4BCLVOThe data when YVU mode & SOUND SYS != M 详细说明附后4BCLVDThe data when YVU mode & SOUND SYS = M 详细说明附后4BOPT2详细说明附后AKB00:AKB off;01:ACB (cut off : align to targets);10:ADB( drive : align to targets);11:AKB ( cut off / drive : align to targets)00SECDSecam mode BIT0:S-ID Sens ; BIT1:Bell fo ; BIT2:S-ID Mode ; BIT3:S-GP phase08HPOS50Hz HORIZONTAL PHASE 50HZ 水平相位（行中心）00 : -3usec ; 10 : 0 ; 1F : +3usec11VP5050 HZ VERTICAL PHASE 50HZ 场中心0 : V phase delay 0H ; 7 : 7H03HIT50HZ VERTICAL AMPLITUDE 50HZ 场幅度00 : -50% ; 20 : 0% ; 3F : 50% ;20HPSSHIFT DAT OF 50/60HZ HORIZONTAL PHASE 行中心偏移量(60Hz 和50Hz的差别)04VP6060HZ VERTICAL PHASE 60HZ 场中心0 : V phase delay 0H ; 7 : 7H01HITSSHIFT DATA OF 50/60 HZ HORIZONTAL PHASE 场中心偏移量60HzVERTICAL AMPLITUDE 60Hz场幅度(60Hz 和50Hz的差别)02VLINV-LINEARITY 场线性 50Hz 0 : -15% ; 8 : 0% ; F : 15% ;08VSCV-S CORRECTION 场S 50Hz 0 : -16% ; 8 : 0% ; F : 16% ;60VLISV-LINEARITY 场线性 60Hz (60Hz 和50Hz的差别)FFVSSV-S CORRECTION 场S 60Hz (60Hz 和50Hz的差别)DPC50HZ E-W PARABOLA 50 HZ 东西枕校 00 : 0Vp-p ; 20 : 1.4 Vp-p ; 3F : 2.8 Vp-p ;00DPCS60HZ E-W PARABOLA 60 HZ 东西枕校 00KEY50HZ TRAPEZIUM 50 HZ 梯形校正 00 : 13% ; 20 : 0% ; 3F : 13% ;00KEYS60HZ TRAPEZIUM 60 HZ 梯形校正00WID50HZ PICTURE WIDTH 50 HZ 行幅00 : 1.5Vp-p ; 20 : 4 Vp-p ; 3F : 6.5 Vp-p ;00WIDS60HZ PICTURE WIDTH 60 HZ 行幅00ECCTEW-CORNER CORRECTION(TOP) 顶部两角校正00 : -1.5Vp-p ; 20 : 0 Vp-p ; 3F : 1.5 Vp-p ;ECCBEW-CORNER CORRECTION(BOTTOM) 底部两角校正00 : -1.5Vp-p ; 20 : 0 Vp-p ; 3F : 1.5 Vp-p ;VEHT帧-高压下尺寸的调整 （改变图象模式可以看出来）03HEHT行-高压下尺寸的调整 00SBYSECAM B-Y08SRYSECAM R-Y08BRTSSUB BRIGHT （C0-00-3F）00RAGCRF AGC ADJUSTMENT RF AGC 调整00 : IF mute ; 01 : 65dB ; 3F : 100 dB ;35HAFC1/2 AFC DATA ADJUSTMENT AFC调整BIT0.1 : TV MODE ; BIT2.3 : AV MODE ;09V01VOLUME OUTPUT DATA AT 1%1FV25VOLUME OUTPUT DATA AT 25%3FV50VOLUME OUTPUT DATA AT 50%4BV100VOLUME 1005DMUTTY-MUTE FOR SOFT START00STATCONTRAST UP TIME FOR SOFT START00FLG0Flag0 详情附后FLG1Flag1 详情附后REFPAKB Ref Pulse Position （00-07）00RSNSR SENS （00-3F）00GSNSG SENS （00-3F）00BSNSB SENS （00-3F）00MODBIT0.BIT1 : akb CUT OFF SENSITIVITY;00:*9.75 ; 01:*10.00; 10:*10.25; 11:*10.50; MOD.3=0 CUT OFF range:-0.65"+0.65; MOD.3=1 CUT OFF range:-0.65"+0.8500STBYBit0,1:IF Standby; Bit2,3: VCD StandbySVMPIC1 SVM00SVM1PIC2 SVM00SVM2PIC3 SVM00SVM3PIC4 SVM00VBLKV BLANKING START AND STOP POINT00VCENV CENTERING 场输出脚直流电平（为1/2Vcc）（不好卷边）19UCOM00:GND;01:R OUTPUT;10:B OUTPUT;11:MONITOR RF AGC VIA ADC00OSD2GAME AND CALENDAR POSTION OSD10PYNXNormal H.SYNC max 判断蓝屏出现28PYNNNormal H.SYNC min 判断蓝屏出现18PYXSSearch H.SYNC max 搜索状态同步判断22PYNSSearch H.SYNC min 搜索状态同步判断1EWCTLFor a-pro data setting 00SUR1SURROUND DATA (MONO)00SUR2Surround data (STEREO1)00SUR3Surround data (STEREO2)00BASCBASS CENTER00BASXBASS MAX00TRECTREBLE CENTER00BALCBALANCE CENTER00WOFCWOOFER CENTER00BAS1SOUND MEMORY1 BASS DATA 剧场00BAS2SOUND MEMORY2 BASS DATA 新闻00BAS3SOUND MEMORY3 BASS DATA 音乐00TRE1SOUND MEMORY1 TREBLE DATA 剧场00TRE2SOUND MEMORY2 TREBLE DATA 新闻00TRE3SOUND MEMORY3 TREBLE DATA 音乐00WFL1SOUND MEMORY1 WOOFER DATA 剧场00WFL2SOUND MEMORY2 WOOFER DATA 新闻00WFL3SOUND MEMORY3 WOOFER DATA 音乐00WON1重低音控制00WON2低音控制00WOFF重低音为关时，输出的重低音音量00COM1梳状滤波器控制00COM2梳状滤波器控制00MODE0详情附后MODE1详情附后MODE2详情附后RCUTSRCUTS00GCUTSGCUTS00BCUTSGDRVS10GDRVSGDRVS00BDRVSBDRVS00NOIS信号强弱界限设定01OSDFOSD频率 数值越大屏幕上字越小65WAIT TIME开机等待时间38CUR_CEN拉幕位置CUR_STEP拉幕速度01PBRI连续按0键 图像所恢复的亮度数值PCOL连续按0键 图像所恢复的彩色数值PCON连续按0键 图像所恢复的对比度数值PSHP连续按0键 图像所恢复的清晰度数值PTIN　 OPT：BITFUNCTION0开机欢迎语 1：有 0：无欢迎语1实时时钟 1：有 0：无2Y Mute ON/OFF when ＣＨ changes(=1:ON 切换频道时为黑屏) 3AUDIO GAIN SW 0：NORMAL ； 1：HIGH ；4Not VT Down of AFT when No Signal(=1) 1：无信号时AFT不自动向下搜台5FS TUNER 1：ALPS TUNE;0:北京松下6Select TV sync(0) or MONITOR sync(1) 选择同步方式 选择17计时收看功能 1：有；0：无　 ABL：(auto bright limit)BITFUNCTION0ABL-Gain 00:-0.2;01:-0.4;10:-0.6;11:-0.8v12ABL Start Point 00:-0.0;01:-0.15;10:-0.3;11:-0.45v34WPS(0:Y peak limiter off 1: Y peak limiter on 105 IRE)5RGB ABCL(0: ABCL active for OSD 1:inactive)6没有定义 71：按用户遥控器上SLEEP键清除收看计时；0：不可注：最终要设置为0，不能设置为1　 DCBSBITFUNCTION0BLACK STRETCH00：Off；01：Black stretch point，25IRE；02：35 IRE；03：45 IRE12Y GAMMA00：Off；01：Y y point 90 IRE,Gain –3dB；02：80 IRE，03：70 IRE34OSD CONTRAST00:80 IRE 01:70;02:60;03:50;56UNUSE70:H,V blanking on 1: H,V blanking off 　　 CLTO\CLTM\CLVO\CLVDBITFUNCTION0Y Delay Time000:-40 nsec;001:0;010:40 nsec;011:80 nsec;100:120 nsec;101:160 nsec;110:200 nsec;111:240 nsec123N Phase00:USA(105 degree);01:Japan(93 degree);10:11:DVD45Color Y 0:Color gamma off ;1:On;6PN-ID Sens 0:PAL/NTSC killer sensitivity,1mVpp; 1:10mVpp7FID 0:Normal;1:Alwas killer off,i.e. always color on..　 FLG0:BITFUNCTION00:NORMAL;1:PIF over modulation switch on10:BPF;1:TOF20:Nyquist Buzz CANcel,on;2:off34567vco readjust when position select 0:dISAble;1:enable;　 FLG1:BITFUNCTION01230:SIF beat down Frequency,1MHz;1:+62.5kHz shift40:Sync separation level,40%;1:36%50:SIF 1MHz convert gain,Low gain;1:High gain67　 VBLKBITFUNCTION000:23H;01:33H;10:37H;11:41H (50Hz)00:22H;01:30H;10:34H;11:38H (60Hz)1200:310H;01:299H;10:295H;11:291H (50Hz)00:263H;01:254H;10:250H;11:246H (60Hz)34567　 WCTLBITFUNCTION0Woofer lpf fo00:100Hz;01:125Hz;10:170Hz;11:210Hz12ALS start point00:220mv;01:380mv;10:525mv;11:770mv34ALS SW 0:OFF;1:ON5Input attenua-tion 0:0dB;1:-5dB6Bass boost SW 0:Off;1:ON7　 COM1:BITFUNCTION0VENH的数据123PDSOFF 数据4No use567　 COM2:BITFUNCTION0VNLR 数据1234COR 数据56No use7　 MODE0:BITFUNCTION01:有拉幕；0：无121：有SECAM制；0：无31：南美制式时设成AUTO；0：不转成AUTO41：218频道；0：100频道51：RGB Out-Cut Off DC；0：Y-MUTE 选择1，否则换台或拉模可能出现灰屏61：有背景灯；0：无71：have VM；0：have not VM　 MODE1:BITFUNCTION01：有YUV输入；0：无(DVD)121：有些屏显一直显示；0：有些屏显有时显示3TINT 0:use 1:unused4TINT polarity ,input to V/C/D. 0:normal 1:invert51:Av mute 6SHOP OUT00：DK；01：I；10：BG7　 MODE2:BITFUNCTION00:无M;1:有10:无I;1:有20:无BG;1:有30:无DK;1:有40:when asm & search,set up VCO adjust req. ,1:only power on5The algorithm of ASM. 0:ASM doesn't judge IFLOCK with case 4. 1:ASM judge IF LOCK with case 46The algorithm of ASM. 0:ASM doesn't judge Fhsync with case 4. 1:ASM judge Fhsync with case 471：有软换台；0：无　 OPT2BITFUNCTION00,V AGC reference,deends on YC Vcc;1,Depends on integrated regulator. 11：有农历 0：无农历 21:only English in 8829B software 31:遥控器有液晶显示； 0：无 注：遥控器有液晶时电视不需显示调整信息41：中频为38.9MHz 0：中频为38MHz51:有倾斜校正功能，无平衡 0:无倾斜校正功能，有音量平衡功能　 MODBITFUNCTION0akb CUT OFF SENSITI VITY00：*9.75;01:*10.00;10:*10.25;11:*10.50123MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.85456  OPT：　BITFUNCTION0Hotel mode 1:have welcome and no 0key 0:no welcome and have 0 key1Real Time Clock 1:have real time clock2V_Mute ON/OFF when ＣＨ changes(=1:ON)3AUDIO GAIN SW of tb12404Not VT Down of AFT when No Signal(=1)5TINT 0:use 1:unused6Select TV sync(0) or MONITOR sync(1)7Mute of av switch key 1.use 0.no use　 ABL：BITFUNCTION0ABL-Gain 00:-0.2;01:-0.4;10:-0.6;11:-0.8v12ABL Start Point 00:-0.0;01:-0.15;10:-0.3;11:-0.45v34WPS 0:Y peak limiter off 1:Y peak limiter on,105IRE5RGB ABCL 0:ABCL active for OSD 0:inactive61：计时收看清到20H；0：计时收看清到0H71：用户可按SLEEP键清除收看计时；0：不可　 DCBS？BITFUNCTION0BLACK STRETCH 黑电平延伸00：Off；01：Black stretch point,26IRE; 10 : 33 IRE; 11 : 43 IRE12Y GAMMA00：Off；01：Y γ point 90 IRE,Gain –3dB; 10 : 82 IRE ; 11 : 75 IRE34OSD CONTRAST00:80 IRE 01:70;02:60;03:50;56UNUSE7BLK　 CLTO\CLTM\CLVO\CLVDBITFUNCTION0Y Delay Time000:-40 nsec;001:0;010:40 nsec;011:80 nsec;100:120 nsec;101:160 nsec;110:200 nsec;111:240 nsec123N Phase00:USA(105 degree);01:Japan(93 degree);10:11:DVD45Color Y 0:Color gamma off ;1:On;6PN-ID Sens 0:PAL/NTSC killer sensitivity,1mVpp; 1:10mVpp7FID 0:Normal;1:Alwas killer off,i.e. always color on..　 FLG0:BITFUNCTION00:NORMAL;1:PIF over modulation switch on10:BPF;1:TOF20:Nyquist Buzz cancel,on;2:off3Q det Gain4L SECAM Mode5SIF FIX Select 0:fix to normal, 1:control with sound system6SIF 5.74 Select In D mode, aPLLy this bit to SIF 5747vco readjust when position select 0:disable;1:enable; FLG1:BITFUNCTION0CW SW1YOUT ON2HD input polarity select30:SIF beat down frequency,1MHz;1:+62.5kHz shift40:Sync separation level,40%;1:36%50:SIF 1MHz convert gain,Low gain;1:High gain for Evalution6DET358 for Evalution7C TRAP PASS for Evalution　 SVM:BITFUNCTION0SVM gain00:-6dB;01:0dB;10:+6dB;11:+12dB12SVM DL(svm delay)00:off;01:-100ns;10:-60ns;11:-40ns34CO MAX 0:cut off range is –0.65"+0.65 ; 1: cut off range is –0.65"+0.8551：有计时收看功能；0：no the total time of watch TV61：有软换台功能；0：no the soft change channel7UNUSE　 VBLKBITFUNCTION000:23H;01:33H;10:37H;11:41H (50Hz)00:22H;01:30H;10:34H;11:38H (60Hz)1200:310H;01:299H;10:295H;11:291H (50Hz)00:263H;01:254H;10:250H;11:246H (60Hz)345　 MODE0:BITFUNCTION01：218频道；0：100频道11：5060 （M制）；0：两路AV （无M制时，几路AV用AV option来控制 ）20：有SECAM制；1：无31：RGB Out-Cut Off DC；0：Y-MUTE41：有些屏显一直显示；0：有些屏显有时显示50:ALPS\1:北松6SHOP OUT00：DK；01：I；10：BG7　 MODE1:BITFUNCTION00:无BG;1:有10:无I;1:有20:无DK;1:有30:无M;1:有40:when asm & search,set up VCO adjust req. ,1:only power on0:PIF VCO adjust trigger 1: normal (12 :bit 7)5The algorithm of ASM. 0:ASM doesn't judge IFLOCK with case 4. 1:ASM judge IF LOCK with case 46The algorithm of ASM. 0:ASM doesn't judge Fhsync with case 4. 1:ASM judge Fhsync with case 47TINT polarity ,input to V/C/D. 0:normal 1:invert AV_OPT：ByteFUNCTIONVideo1Video2Video30VIDEODVD1VIDEOS-VIDEODVD2VIDEODVDVIDEO3VIDEOS-VIDEODVD4VIDEO/S-VIDEODVD5VIDEO/S-VIDEOVIDEODVD6VIDEODVDVIDEO7VIDEOVIDEODVD　 OPT2:BITFUNCTION0lunar calendar 1:have lunar calendar ; 0:no lunar calendar11:调整时间时不可以在电视机上显示 0：调整时间时可以在电视机上显示 21：只有英文 0：有中文3AV是否静噪；1：静噪；0：不4有无背景灯；1：有；0：无5No use6No use7No use一直设置为0即可。　 MOD：BITFUNCTION0akb CUTOFF SENSITI VITY00：*9.75;01:*10.00;10:*10.25;11:*10.50123MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.854000：无；001：45.75；011：38.9；100：38.0567上一页12【内容导航】 第1页：第2页：8829BV1.0软件D 模式参数调整第3页：D(8829B-2.0) 模式参数调整