|
|
|
东芝8829B总线数据进入总线方法同8803机芯总线数据如下：8829B1.0总线数据8829BV1.0软件D 模式参数调整参数名参数描述默认值 OSD位置OSD的起始位置20 OPT选项OPTION，具体说明附后DC/FC RCUTR CUT OFF 红截止(00-FF)66 GCUTG CUT OFF 绿截止(00-FF)37 BCUTB CUT OFF 兰截止(00-FF)29 GDRVG DRIVE 绿驱动(00-7F)3B BDRVB DRIVE 兰驱动(00-7F)40 CNTXSUB CONTRAST MAX 副对比度最大值(00-7F)7F BRTCSUB BRIGHT CENTER 副亮度中间值(00-7F)5A COLCSUB COLOR CENTER FOR NTSC 副彩色NTSC中间值(00-7F)42 TNTCSUB TINT CENTER 副色调中间值(00-7F)42 COLPSUB COLOR CENTER FOR PAL 副色度PAL中间值(80-00-7F)08 COLSSUB COLOR CENTER FOR SECAM 副色度SECAM中间值(00-7F)31 DCOLDVD-色毒幽值45 SCOLCr input(#21) gain up,000"111:0dB;1.1dB;1.9dB;2.5dB;3.0dB;3.3dB;3.6dB;3.9dB07 SCNTY-SUB CONTRAST Y信号副对比度(00-7F)0E CNTCSUB CONTRASRT CENTER 副对比度中间值(00-7F)50 CNTNSUB CONTRASRT MINIMUM 副对比度最小值(00-7F)00 BRTXSUB BRIGHT MAX 副亮度最大值(00-7F离中间值上限)40 BRTNSUB BRIGHT MINIMUM 副亮度最小值（00-7F离中间值下限）40 COLXSUB COLOR MAX 副色度最大值3F COLNSUB COLOR MINIMUM 副色度最小值(00-7F)00 TNTXSUB TINT MAX 副色调最大值(00-7F离中间值上限)40 TNTNSUB TINT MINIMUM 副色调最小值(00-7F离中间值下限)40 ST3SUB SHARP CENTER NTSC3.58 IN TV副画质中间值（NTSC3.58 IN TV）(00-3F)20 SV3SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值（NTSC3.58 IN VIDEO）(00-3F)20 ST4SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值（OTHER COLOR SYSTEM IN TV）(00-3F)20 SV4SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值（OTHER COLOR SYSTEM IN VIDEO）(0-3F)20 SVDSUB SHARP CENTER IN DVD (00-3F)19 ASSHASYMMETRY – SHARPNESS 不对称(单边清楚度)07 SHPXSUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值38 SHPNSUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值1A TXCXRGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 对比度的最大值图文状态（UNUSEFUL）1F RGCNRGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 对比度的最小值图文状态（UNUSEFUL）00 ABLABL，具体说明附后37 DCBSDCBS，具体说明附后23 CLTOThe data when TV mode & SOUND SYS NOT M 具体说明附后06 CLTMThe data when TV mode & SOUND SYS IS M 具体说明附后06 CLVOThe data when NOT YVU mode 具体说明附后47 CLVDThe data when YVU mode 具体说明附后41 OPT2具体说明附后03 AKB00:AKB off;01:ACB(cutoff:align to targets);10:ADB(drive:align to targets);11:AKB(cutoff/drive:align to targets)00 SECDSecam mode BIT0：S-ID Sens，BIT1：Bell fo，BIT2：S-ID ModeBIT3：S-GP phase 08 HPOS50HZ HORIZONTAL PHASE 50HZ 水平相位（行中心）00:-3usec; 10:0; 1F:+3usec0E VP5050 HZ VERTICAL PHASE 50HZ 场中心0:V phase delay 0H; 7: 7H06 HIT50HZ VERTICAL AMPLITUDE 50HZ 场幅度00:-50%; 20: 0%; 3F:50& HPSSHIFT DAT OF 60HZ HORIZONTAL PHASE 行中心偏移量(60Hz和50Hz的差异)03 VP6060HZ VERTICAL PHASE 60HZ 场中心0:V phase delay 0H; 7: 7H03 HITS60HZ VERTICAL AMPLITUDE 60HZ场幅度(60Hz和50Hz的差异)00 VLINV-LINEARITY 场线性 50Hz 0:-15%; 8:0%; F:15%09 VSCV-S CORRECTION 场S 50Hz 0:-16%; 8:0%; F:16%09 VLISV-LINEARITY 场线性 60Hz (60Hz和50Hz的差异)00 VSSV-S CORRECTION 场S 60Hz (60Hz和50Hz的差异)00 DPC50HZ E-W CORRECTION 东西枕校00:0VP-P;20:1.4VP-P;3F:2.8VP-P1E DPCS60HZ E-W CORRECTION (60Hz和50Hz的差异)01 KEY50HZ TRAPEZIUM CORRECTION 梯形校正00:13%; 20:0%; 3F:13%24 KEYS60HZ TRAPEZIUM CORRECTION 梯形校正(60Hz和50Hz的差异)01 WID50HZ PICTURE WIDTH 行幅00:1.5VP-P;20:4VP-P;3F:6.5VP-P15 WIDS60HZ PICTURE WIDTH 行幅 (60Hz和50Hz的差异)01 ECCTEW-CORNER CORRECTION TOP 顶部两角校正00:-1.5VP-P;20:0VP-P;3F:1.5VP-P0B ECCBEW-CORNER CORRECTION BOTTOM 底部两角校正00:-1.5VP-P;20:0VP-P;3F:1.5VP-P0E VEHT帧幅随高压波动的幅度（改变图象模式可以看出）03 HEHT行幅随高压波动的幅度00 SBYSECAM B-Y08 SRYSECAM R-Y08 BRTSSUB BRIGHT (C0-00-3F)00 RAGCRF AGC ADJUSTMENT RF AGC 调整00:IF mute; 01: 65dB; 3F: 100dB30 HAFC1/2 AFC DATA ADJUSTMENT AFC调整BIT1,0:TV MODE BIT2,3:AV MODE00 V01VOLUME OUTPUT DATA AT 1%10 V25VOLUME OUTPUT DATA AT 25%3F V50VOLUME OUTPUT DATA AT 50%48 V100VOLUME 10054 MUTTY-MUTE TIME OF SOFT START00 STATCONTRAST UP TIME OF SOFT START00 ***0Flag0 (00-FF) 详情附后52 ***1Flag1 (00-FF) 详情附后24 REFPAKB Pulse Position (00-07)00 RSNSR SENS (00-3F)00 GSNSG SENS (00-3F)00 BSNSB SENS (00-3F)00 MOD00:akb CUTOFF SENSITIVITY,*9.75;01:*10.00;10:*10.25;11:*10.50; MOD.3:0 CUTOFF range:-0.65"+0.65;1:-0.65"+0.8500 STBYBit0,1:IF Standby; Bit2,3: VCD Standby00 SVMPIC1 SVM00 VBLKV BLANKING START AND STOP POINT00 VCENV CENTERING场输出脚直流电平（为1/2VCC）（不好卷边）19 UCOM1C OSD2GAME AND CALENGDAR POSITION18 PYNXNormal H.SYNC max判定蓝屏出现28 PYNNNormal H.SYNC min判定蓝屏出现18 PYXSSearch H.SYNC max搜索状态同步判定22 PYNSSearch H.SYNC min搜索状态同步判定1E WCTL"COM2NO USE（TOGETHER 23 ITEMS）00 MODE0详情附后31 MODE1详情附后2D MODE2详情附后FF RCUTSRCUTS00 GCUTSGCUTS00 BCUTSGDRVS00 GDRVSGDRVS00 BDRVSBDRVS10 NOIS信号强弱界限设定01 OSDFOSD频率；数字小，字符增大，右移。58 WAIT TIME开机等待时间38 CUR_CEN拉幕位置AC CUR_STEP拉幕速度01 |
|
/1 
|手机版|粤ICP备13038386号|粤ICP备13038386号|美丽的网站-英华家电维修论坛
( 粤ICP备13038386号 )
站长邮箱 505966338@qq.com
发表于 2011-3-27 23:22:55
QQ好友和群
QQ空间
腾讯微博
腾讯朋友
微信
收藏
分享
支持
反对